The matter was that during checking wires of a shape for small area, non-outer wires were checked with constructing a new face with BRepBuilderAPI_MakeFace. If a face has location an edge from original face has no pcurve on the constructed face, which leads to exception in BRepGProp::SurfaceProperties. The fix constructs new face using EmptyCopy.
The method ShapeAnalysis_Wire::CheckSmallArea() has been changed so as to check area of the outer wire without hole-wires. API of this method has been changed, as the second argument theIsOuterWire is not needed any more.
The test cases have been updated, below are explanations of changes:
test de iges_2 G7
The fixed version leaves a wire in a face, but the master version considered it small and removed. The master version works wrong. It is because the face built with this wire has negative area, but the code in CheckSmallArea function does not get absolute value before comparing area with the tolerance. The left wire leads to splitting of the face on two, checkshape error in the face, and statshape faulty due to increased number of faces in the second pass.
test de iges_2 G2
The fixed version leaves a wire that is removed in the master version. The cause is the same as in G7 test case. However, here the problematic wire has very big tolerance. So, when the fixed version left it in the shape, the overall maximal tolerance became much greater than in reference data.
test de step_3 E6
In fixed version a really bad small wire is removed from the face, while in master version it is left and produces an error in checkshape report. So, it is an improvement.
- New methods SetLinearTolerance and SetAngularTolerance have been added in the class ShapeUpgrade_UnifySameDomain.
- The algorithm has been modified to consider these tolerances when checking if two faces are same domain.
- The draw command unifysamedomain has been changed to accept new parameters.
- The internal method MergeSeq has been changed to avoid exception connected with access to unknown key in the data map.
Create test case
Small correction of test case for issue CR27729
Upgrade check of closeness of 2dcurve to line during projection:
For C1 and more surfaces check distance to normal, not to surface, for C0 surfaces update tolerance formula.
Add check for possible period jump in some inner point.
Update some test cases.
Add cache saving for lines,
update fixPeriodicTroubles() function, using parameters from cashe.
Small correction of test cases for issue #26930
fix processing of points from cache.
Update of test cases according to the new behavior
Fix behavior of fixPeriodicityTroubles() on different isolines,
fix copy/paste mistake.
Update test cases:
iges_2 C4 - return to master values
step_3 E6 - improvement.
Performance of the algorithm ShapeUpgrade_UnifySameDomain has been improved by avoiding of multiple calls of ShapeBuild_ReShape::Apply() method.
New test cases have been added.
Add checks to avoid exceptions.
Remove check for small 3D curve, now pcurve will be built for all small edges, which have not been removed by FixSmall.
- Added function checkprops, set default tolerance parameter to 1.0e-4
- Using "area" instead of "square".
- Options "-equal\notequal" isn't used together with "-s" in blend and offset test cases.
- Correct regressions/differences/improvements and CPU problem (set props tolerance to 0.1)
- Corrected test cases to use checkprops proc.
- Correct image difference
- Updated TODOs in test cases.
- Updated test cases to get correct images of result shape
Context usage extended in method ShapeFix_Wire::FixSelfIntersection() to avoid modification of original shape by shape healing.
Added check for subshape modification in XSAlgo/XSAlgo_AlgoContainer::MergeTransferInfo().
Test cases are updated to the new behaviour.
Test case for issue CR24658
Added possibility to define patterns that must be present in the test log, so that test is considered OK only if all these patterns are found.
New REQUIRED statement is introduced for that, documented in dox/dev_guides/tests/tests.md.
Removed all uses of decho and dlog commands, added REQUIRED where necessary.
Command xdistcs is modified to output to Tcl instead of cout, and extended to report errors and warnings if distances are greater than tolerance (directly, instead of complex post-processing on Tcl level).
DEBUG mode for TODOs was removed (we should have no deviations in Debug mode).
Corrected indentation in DrawResources/TestCommands.tcl
HTML log will now highlight TODO statement causing IMPROVEMENT status, or REQUIRED statement causing FAIL, by corresponding color.
Added set of methods CopyVertex in BRepTools_ReShape. Usage of this non-modifying methods added in ShapeFix_Wire, ShapeFix_Edge.
Test case for issue 26656.
Test cases updated to the new behavior.
Correction of test cases for issue CR26656
Changed access by value to access by reference in method CopyVertex.
Algorithm of computation of safe shift value along 2D-line (in order to distance between two points was less than tolerance) has been improved.
Correction of some test cases in accordance with their new behavior.
Test-case for issue #26642
Small correction of test-case
Small correction of test-case bugs heal bug26642
Modification to support case when edges on face have incorrect orientation was added.
Modification to support case when wires have intersecting segment was added
Test cases for issue 25553 added; other affected tests corrected (improvements)
Corrected test case
Treat internal edges in proper way to save them in the result.
The test "bugs heal bug26489_4" has been modified to reflect the actual behavior.
Test-case for issue #26635
Attached invalid shape is represented by solid containing one face twice.
Protection from such case was added in ShapeFix_Shell class.
Creation of COMPSOLID was modified for case when shells composing COMPSOLID have the same shared faces in order to prevent hanging.
Small modification.Protection to avoid exception
Test-case for issue #26408
Avoid merging edges if the collapsed vertex has a third connected edge.
Fix the problem when merged edges have different location.
Test case for issue CR26219
Additional fix to improve robustness.
Test cases for issue CR26219
Small correction of test cases for issue CR26219
The analysis of small area in the method ShapeAnalysis_Wire::CheckSmallArea is performed the following way:
- On the fisrt step algorithm produces a rough estimation of part of surface area.
- In a case if obtained estimation is less than tolerance then evaluate real area and comapre this value with tolerance.
- New flag has been added to XSTEPResource/IGES. In a case if flag is true the faces with small 3d area is removed from ShapeFix context.
Test-case for issue #25923 and update test-cases in de group according to the new behavior.
Unstable test cases were reviewed
Modified test cases using checktrend command
Modified test cases for Linux platform
Modified test cases for Debug mode
Recalculate of tolerance before edge cutting
Test case for issue CR25013
add try to increase tolerance before splitting in singularity during PCurve adding.
Correction of test cases for issue CR25013
Usage of Projlib added in case of uneven points distribution.
Test cases are updated to the new behavior.
Test cases for issue CR17129
Correction of test case for issue CR17129
The number of points to divide the edge curve on a segments to compute a
boundary box does not provide a good tolerance. So a resultant boundary
box has an incorrect bounds. As a result the intersection near to a
tangent of curve does not detected.
Test case for issue CR25823
The reason of FAIL status of FixGaps3d is that the trying to convert
curves to BSplines on valid edges (both adjacent points saticfy a
precision) leads to skipping of the convertation and gives wrong status.
Check of the gap on adjacent points before try ro convert curves was added.
Test-case for issue #24881
Check whether p-curve being projected can be approximated by straight line is made before full-scale projection, to improve performance.
If straight, pcurve is created as Line only if this will lead to the same range parameterization as 3d curve, otherwise BSpline of degree 1 is created.
Re-approximation of line pcurves by bsplines removed from ShapeFix_Edge.
Test case updating to new behavior.
Added "static" keyword to the fixPeriodictyTroubles() function.
Update of test-cases according new behavior
Added check and fix of tolerances of all vertices after performing all fixes.
It is necessary to avoid situation when point of vertex belonging a few faces was changed for current face
but edges containing this vertex belonging before fixed face are not taking into account.
Mode FixVertexTolMode to manage check tolerance of vertices was added in ShapeFix_Shape
class. (default value is equal to -1)
Method to change FixVertexTolMode mode FixVertexTolMode() was added in ShapeFix_Shape class
Test case for CR25455
1. DRAW-commands for curve/surface continuity returning were changed.
2. Output of "distmini" DRAW-command is amended.
3. Function MinMax() was moved from Standard_Real to IntPatch_ImpImpIntersection_4.gxx.
4. Incorrect computing of nbcurveC1 in Geom2dConvert::C0BSplineToC1BSplineCurve(...) function was liquidated.
Test cases were changed.
Fix contains protection in order to avoid addition in result wires INTERNAL or EXTERNAL edges during connecting edges in wires.
Test case for issue #25333
fix the notched edges twice per face - before checking for missing seam and after
Test case correction for issue CR24983
Add check for invalid Surface of linear extrusion (with basis curve - line and extrusion direction parallel to this line) during converting STEP surface
Small corrections of test cases for issue CR24983
MAIN CHANGES:
FixAddNaturalBound: the boundaries of "natural bound addition" are restricted: a face, that does not contains an outer wire, should not have any infinite UV boundaries due to new face building (with using a surface) requires specified UV boundaries.
FixAddNaturalBound: myResult is updated in FixAddNaturalBound when the method creates a new face with natural boundary. myResult is required to be updated for next "fix small-area wires" algorithm
IsPeriodicConicalLoop: incorrect working BRepTools_WireExplorer was replaced on TopoDS_Iterator.
a natural bound is added to all the faces are constructed with UV-periodical surfaces (not only sphere and torus; e.g., closed b-splines)
other:
ShapeAnalysis: ReverceSeq renamed to ReverseSeq
BRep_Tool Pnt and Tolerance has the check for null TShape
Test cases for issue CR24249
required null checks were added
test cases were corrected according to their new behavior
Correction test case for issue CR24249
