Implementation of Fuzzy Boolean operations. Such operations allow to perform Boolean operations on the shapes
with near-coincidence between the entities of these shapes, i.e. between shapes in which some entities from one shape
are intended to be coincide with some entities from the other, but the coincidence is not precise.
API for Boolean operations has been improved to have a possibility to add new options.
Modified entities:
1. New option of setting additional tolerance have been added to the following classes:
class BOPAlgo_ArgumentAnalyzer
class BOPAlgo_BOP
class BOPAlgo_Builder
class BOPAlgo_MakerVolume
class BOPAlgo_PaveFiller
class BOPDS_DS
class BRepAlgoAPI_BooleanOperation
class BRepAlgoAPI_Check
class BRepAlgoAPI_Common
class BRepAlgoAPI_Cut
class BRepAlgoAPI_Fuse
class BRepAlgoAPI_Section
2. Following draw commands have been modified to support new functionality:
BOP commands:
bop b1 b2 [tol]
bcommon r b1 b2 [tol]
bcut r b1 b2 [tol]
bfuse r b1 b2 [tol]
bsection r s1 s2 [-n2d/-n2d1/-n2d2] [-na] [tol]
mkvolume r b1 b2 ... [-c] [-ni] [-s] [tol]
bfillds [-s -t] [tol]
Check commands:
bopcheck Shape [level of check: 0 - 9] [-t -s] [-tol tol]
bopargcheck [-F/O/C/T/S/U] [/R|F|T|V|E|I|P|C|S]] [#BF] [-tol tol]
3. Two new classes have been added to API to provide the root interface for algorithms
class BRepAlgoAPI_Algo
class BRepAlgoAPI_BuilderAlgo
Fix to eliminate the warning.
Test-cases for issue #25477
Calculation of last parameter of projected curve was changed for the projecting of a curve to surface of revolution, if the curve is intersected with the axis of revolution
Test case for issue CR25494
Added check and fix of tolerances of all vertices after performing all fixes.
It is necessary to avoid situation when point of vertex belonging a few faces was changed for current face
but edges containing this vertex belonging before fixed face are not taking into account.
Mode FixVertexTolMode to manage check tolerance of vertices was added in ShapeFix_Shape
class. (default value is equal to -1)
Method to change FixVertexTolMode mode FixVertexTolMode() was added in ShapeFix_Shape class
Test case for CR25455
1. Function IsSame(...) for IntSurf_PntOn2S was added (see IntSurf_PntOn2S.cdl for detail information).
2. Inserting additional points is forbidden if existing WLine contains only two points coincided.
Test-case for issue #25488
Do not clean polygons that are created for different faces not connected with current shape.
Remove old code producing additional points for BSpline curves due to fix#24959.
Test cases fir issue CR25469
Revert changes producing additional points for BSpline curves with C1 continuity
Test cases fir issue CR25469
Correction of test cases for issue CR25469
Changes:
1. class IntTools_FaceFace
method:
void IntTools_FaceFace::MakeCurve(const Standard_Integer Index,
const Handle(Adaptor3d_TopolTool)& dom1,
const Handle(Adaptor3d_TopolTool)& dom2)
The value of testing parameter has been changed for the cases of infinite curves
Test case for issue CR25456
Changes:
1. class IntTools_EdgeFace
method:
Standard_Boolean IntTools_EdgeFace::CheckTouchVertex
(const IntTools_CommonPrt& aCP,
Standard_Real& aTx)
The parametric size of the contact zone between vertex and face has been changed
Test cases for issue CR25449
Changes:
class BOPAlgo_PaveFiller
method:
void BOPAlgo_PaveFiller::PerformEF()
The index of the face has been added in post-treatment map
Test cases for issue CR25450
Correction of test case for issue CR25450
Changes:
class BOPTools_AlgoTools
static function:
Standard_Boolean FindPointInFace(const TopoDS_Face& aF,
const gp_Pnt& aP,
gp_Dir& aDB,
gp_Pnt& aPOut,
Handle(IntTools_Context)& theContext,
GeomAPI_ProjectPointOnSurf& aProjPL,
const Standard_Real aDt,
const Standard_Real aTolE)
Binormal calculation starts from the point located outside the tolerance circle of the edge
Test case for issue CR25432
Correction of test cases for issue CR25432
OSD_OpenFile.hxx header is created for using in file open operations with Unicode names.
Fix for STEP files reading.
Adding test cases for issue 25367
Update test case for issue 25364
Update test cases due to improvements
Don't create data structures for whole set of faces. Necessary structures are created directly in BRepMesh_FastDiscret.
Don't copy nodes data during scaling, single structure is used.
Remove lines used for debug
Fix sphere: resolve problem came from merging.
Keep code clean - remove unnecessary logic, expected to be used for complicated restoration process.
Test cases for issue CR25364
Modifications:
1. class BOPTools_AlgoTools
1.1. method
Standard_Boolean BOPTools_AlgoTools::ComputeTolerance
(const Handle(Geom_Curve)& theCurve3D,
const Handle(Geom2d_Curve)& theCurve2D,
const Handle(Geom_Surface)& theSurf,
const Standard_Real theFirst,
const Standard_Real theLast,
Standard_Real& theMaxDist,
Standard_Real& theMaxPar)
It computes the max distance between points taken from 3D and 2D curves by the same parameter
1.2. method
Standard_Boolean BOPTools_AlgoTools::ComputeTolerance
(const TopoDS_Face& theFace,
const TopoDS_Edge& theEdge,
Standard_Real& theMaxDist,
Standard_Real& theParameter)
Computes the valid value of the tolerance for the edge using the function above.
2. Added possibility to check shape on the validity of the curves on the surfaces.
2.1. New status BOPAlgo_InvalidCurveOnSurface has been added to the enumeration BOPAlgo_CheckStatus
2.2. class BOPAlgo_ArgumentAnalyzer
method
void BOPAlgo_ArgumentAnalyzer::TestCurveOnSurface()
It checks each edge/face pair in the shape using the method ComputeTolerance from BOPTools_AlgoTools and stores invalid pairs to myResults.
Invalid pairs are those which contain the edge with tolerance value less then the value computed by the ComputeTolerance method.
2.3. class BOPAlgo_CheckResult
Added new fields:
myMaxDist1 : Real from Standard;
myMaxDist2 : Real from Standard;
myMaxPar1 : Real from Standard;
myMaxPar2 : Real from Standard;
and corresponding setters and getters.
These fields are used to store the results of the TestCurveOnSurface() check.
3. Added new option to the bopargcheck command and two new commands.
class BOPTest_CheckCommands
3.1. command bopargcheck
As it is using the BOPAlgo_ArgumentAnalyzer class to check the shapes
it checks also the validity of the curves on the surfaces.
The output for the invalid shapes is following:
Draw[]> bopargcheck b2 /ic #f
Made faulty shape: s1COnS_1 (MaxDist = 0.0013334343378738308, MaxPar = 0.02884285498274167)
Made faulty shape: s1COnS_2 (MaxDist = 0.0013334340648766174, MaxPar = 0.02884285497934707)
Made faulty shape: s1COnS_3 (MaxDist = 0.0013335086668628978, MaxPar = 1.4133051942712607)
Made faulty shape: s1COnS_4 (MaxDist = 0.0013335086525838983, MaxPar = 1.4133051942713901)
Faulties for FIRST shape found : 4
---------------------------------
Shapes are not suppotrted by BOP: NO
Self-Intersections : NO
Check for SI has been aborted : NO
Too small edges : NO
Bad faces : NO
Too close vertices : NO
Too close edges : NO
Shapes with Continuity C0 : NO
Invalid Curve on Surface : YES Cases(4) Total shapes(8)
Faulties for SECOND shape found : 0
The compounds s1COnS_* contain pair of edge and face.
MaxDist is maximal distance between points taken from 3D curve of the edge and 2D curve of that edge on the face.
MaxPar is a parameter in which the MaxDist is reached.
To disable this check it is necessary to use option /S (bopargcheck shape /S).
3.2. command xdistef
Usage of the command:
xdistef edge face
It computes distance between points taken from 3D curve of the edge and 2D curve of that edge on the face.
Example:
Draw[]> explode s1COnS_1
s1COnS_1_1 s1COnS_1_2
Draw[]> whatis s1COnS_1_1
s1COnS_1_1 is a shape EDGE FORWARD Modified Orientable
Draw[]> whatis s1COnS_1_2
s1COnS_1_2 is a shape FACE FORWARD Modified Orientable
Draw[]> xdistef s1COnS_1_1 s1COnS_1_2
Max Distance = 0.0013334343378738308; Parameter on curve = 0.02884285498274167
3.3. command checkcurveonsurf
Usage of the command:
checkcurveonsurf shape.
It checks each edge/face pair in the shape using the method ComputeTolerance from BOPTools_AlgoTools.
Example:
Draw[]> checkcurveonsurf b2
Invalid curves on surface:
edge e_0 on face f_0 (max dist: 0.0013334343378738, parameter on curve: 0.0288428549827417)
edge e_1 on face f_0 (max dist: 0.0013334340648766, parameter on curve: 0.0288428549793471)
edge e_2 on face f_1 (max dist: 0.0013335086668629, parameter on curve: 1.4133051942712607)
edge e_3 on face f_1 (max dist: 0.0013335086525839, parameter on curve: 1.4133051942713901)
Sugestions to fix the shape:
explode b2 e;
settolerance b2_6 0.0013335086668629;
settolerance b2_7 0.0013334343378738;
settolerance b2_8 0.0013334340648766;
settolerance b2_10 0.0013335086525839;
The command gives suggestions to fix the shape by increasing tolerance values of the invalid edges.
In some cases the tolerance values suggested by the tool can be very large.
Such values should be used very carefully, because setting large tolerance values to the sub-shapes
of the shape can make it non valid (self-interfered) or lead to unexpected result when using
such shapes in some operations (boolean for example).
Test case for issue CR25410
class IntTools_EdgeEdge
method
void IntTools_EdgeEdge::FindSolutions(const IntTools_Range& theR1,
const IntTools_Range& theR2,
const Bnd_Box& theBox2,
IntTools_SequenceOfRanges& theRanges1,
IntTools_SequenceOfRanges& theRanges2)
Looking for the solutions of the intersection between edges with greater precision.
Test cases for the issue.
An improved RWSTL::ReadFile() method + a draw-command returning the number of nodes and triangles for a MeshVS_Mesh object based on STL mesh data source.
An indexed map of points is replaced by a CellFilter of XYZ objects already implemented in BRepBuilderAPI.
Also, BRepBuilderAPI_VertexInspector became exported for TKTopAlgo library (Standard_EXPORT is added for the methods of this class).
Standard_EXPORT is removed for in-line methods of BRepBuilderAPI_VertexInspector
Test-case for issue #25405
Update of test-cases, according to new behavior
Changed next point computation in IntWalk_PWalker.cxx.
Now trying to walk over another isoline if new point is too close to previous.
Test case for issue CR25380
