! Resource file for data exchange between EUCLID3, Styler and CATIA V4 via BRep ! ! LEVEL: ADVANCED WITH GAPS FIXING ! ! For meaning of parameters refer to the end of the file ! ! WARNING: Parameters ! FromV4.FileName, ! ToV4.FileName, ! Reject.FileName, ! FromV4.TraceFileName, ! ToV4.TraceFileName, ! FromE3.TraceFileName, ! ToE3.TraceFileName ! can be configured in accordance with local system conventions. ! By default, they are automatically set in the file .MDTV pointed by variable ! CSF_MDTVDefaults. ! They can be redefined using CSF_MDTVSiteDefaults, CSF_MDTVGroupDefaults or ! CSF_MDTVUserDefaults environment variables to point to the directory where ! file .MDTV with definitions of these parameters is located. ! ============================================================================== ! ! Parameters for CATIA V4 ! Version : 1 !Reject.FileName : /tmp/reject.brep *.TraceLevel : 1 *.MaxTolerance : 0.1 *.SegmentSurfaceMode : 1 ! ------------------------------------------------------------------------------ ! Conversion CATIA V4 -> BRep FromV4.FileName : /tmp/FromV4.brep FromV4.ConvCurvesToBezier : 1 FromV4.ConvSurfacesToBezier : 0 FromV4.SameParameter : 1 FromV4.TraceFileName : /tmp/fromcatiav4.log FromV4.TraceFileAppend : 0 FromV4.TraceLevel : 2 FromV4.SharingFaces : 0 ! ------------------------------------------------------------------------------ ! Conversion BRep -> CATIA V4 ToV4.FileName : /tmp/ToV4.brep ToV4.CurveMerge : 1 ToV4.CreateSkin : 0 ToV4.ShortEdgeRemove : 1 ToV4.ThinFaceRemove : 1 ToV4.FillHoles : 1 ToV4.Prepare : 1 ToV4.TraceFileName : /tmp/tocatiav4.log ToV4.TraceFileAppend : 0 ToV4.TraceLevel : 2 ToV4.KeepCSGHistory : 1 ! Sequence of operators ! Two possible alternatives: to convert to CATIA multi-patch or not ! To avoid construction of CATIA multi-patches use the sequence below ! ToV4.exec.op : DirectFaces,ElementaryToRevolution,SplitAngle,SameParameter,SplitClosedFaces,SameParameter,FixFaceSize,BSplineRestriction,DropSmallEdges,FixGaps,SameParameter,ToBezier ToV4.exec.op : DirectFaces,ElementaryToRevolution,SplitAngle,SameParameter,SplitClosedFaces,SameParameter,FixFaceSize,BSplineRestriction,DropSmallEdges,BSplineRestriction,SameParameter ! complete ToV4.exec.op : see above ! partial ToV4.exec.op : DirectFaces,ElementaryToRevolution,SplitAngle,SameParameter,SplitClosedFaces,SameParameter,BSplineRestriction,SameParameter,ToCATIAGeom ! Parameters of operators ToV4.SplitAngle.Angle : 3.1415928 ToV4.SplitAngle.MaxTolerance : 0.1 ToV4.SplitAngle.SegmentSurfaceMode : 1 ToV4.SplitClosedFaces.NbSplitPoints : 1 ToV4.SplitClosedFaces.CloseTolerance : 0.05 ToV4.SplitClosedFaces.MaxTolerance : 0.1 ToV4.SplitClosedFaces.SegmentSurfaceMode : 1 ToV4.FixFaceSize.Tolerance : 0.05 ToV4.FixGaps.Tolerance3d : 0.05 ToV4.FixGaps.SurfaceMode : 0 ToV4.FixGaps.SurfaceAddSpans : 0 ToV4.FixGaps.SurfaceContinuity : C1 ToV4.FixGaps.NbIterations : 10 ToV4.FixGaps.Beta : 200.0 ToV4.FixGaps.Coeff1 : 0.0 ToV4.FixGaps.Coeff2 : 0.0 ToV4.FixGaps.Coeff3 : 10.0 ToV4.FixGaps.Coeff4 : 0.0 ToV4.FixGaps.Coeff5 : 0.0 ToV4.FixGaps.Coeff6 : 0.0 ToV4.FixGaps.MaxDeflection : 1.0 ToV4.DropSmallEdges.Tolerance3d : 0.05 ToV4.SurfaceToBSpline.LinearExtrusionMode : 1 ToV4.SurfaceToBSpline.RevolutionMode : 1 ToV4.SurfaceToBSpline.OffsetMode : 1 ToV4.BSplineRestriction.SurfaceMode : 1 ToV4.BSplineRestriction.Curve3dMode : 1 ToV4.BSplineRestriction.Curve2dMode : 1 ToV4.BSplineRestriction.OffsetSurfaceMode : 1 ToV4.BSplineRestriction.OffsetCurve3dMode : 1 ToV4.BSplineRestriction.OffsetCurve2dMode : 1 ToV4.BSplineRestriction.LinearExtrusionMode : 1 ToV4.BSplineRestriction.RevolutionMode : 1 ToV4.BSplineRestriction.Tolerance3d : 1e-3 ToV4.BSplineRestriction.Tolerance2d : 1e-5 ToV4.BSplineRestriction.Continuity3d : C1 ToV4.BSplineRestriction.Continuity2d : C1 ToV4.BSplineRestriction.RequiredDegree : 15 ToV4.BSplineRestriction.RequiredNbSegments : 100 ToV4.BSplineRestriction.PreferDegree : 1 ToV4.BSplineRestriction.RationalToPolynomial : 1 ToV4.BSplineRestriction.MaxDegree : 15 ToV4.BSplineRestriction.MaxNbSegments : 10000 ToV4.BSplineRestriction.SegmentSurfaceMode : 1 ToV4.ToBezier.EdgeMode : 0 ToV4.ToBezier.SurfaceMode : 1 ToV4.ToBezier.PlaneMode : 1 ToV4.ToBezier.RevolutionMode : 1 ToV4.ToBezier.ExtrusionMode : 1 ToV4.ToBezier.BSplineMode : 1 ToV4.ToBezier.Curve3dMode : 1 ToV4.ToBezier.Curve2dMode : 1 ToV4.ToBezier.Line3dMode : 1 ToV4.ToBezier.Circle3dMode : 1 ToV4.ToBezier.Conic3dMode : 1 ToV4.ToBezier.MaxTolerance : 0.1 ToV4.ToBezier.SegmentSurfaceMode : 1 ToV4.ToBezier.MinCurveLength : 0.05 ToV4.FixShape.Tolerance3d : 1.e-7 ToV4.FixShape.MaxTolerance3d : 1.e-7 ToV4.FixShape.MinTolerance3d : 1.e-7 ToV4.FixShape.FixFreeShellMode : -1 ToV4.FixShape.FixFreeFaceMode : -1 ToV4.FixShape.FixFreeWireMode : -1 ToV4.FixShape.FixSameParameterMode : -1 ToV4.FixShape.FixSolidMode : -1 ToV4.FixShape.FixShellMode : -1 ToV4.FixShape.FixFaceMode : -1 ToV4.FixShape.FixWireMode : -1 ToV4.FixShape.FixOrientationMode : -1 ToV4.FixShape.FixMissingSeamMode : -1 ToV4.FixShape.FixSmallAreaWireMode : -1 ToV4.FixShape.ModifyTopologyMode : 0 ToV4.FixShape.ModifyGeometryMode : 1 ToV4.FixShape.ClosedWireMode : 1 ToV4.FixShape.PreferencePCurveMode : 1 ToV4.FixShape.FixReorderMode : -1 ToV4.FixShape.FixSmallMode : -1 ToV4.FixShape.FixConnectedMode : -1 ToV4.FixShape.FixEdgeCurvesMode : -1 ToV4.FixShape.FixDegeneratedMode : -1 ToV4.FixShape.FixLackingMode : -1 ToV4.FixShape.FixSelfIntersectionMode : -1 ToV4.FixShape.FixReversed2dMode : -1 ToV4.FixShape.FixRemovePCurveMode : -1 ToV4.FixShape.FixRemoveCurve3dMode : -1 ToV4.FixShape.FixAddPCurveMode : -1 ToV4.FixShape.FixAddCurve3dMode : -1 ToV4.FixShape.FixSeamMode : -1 ToV4.FixShape.FixShiftedMode : -1 ToV4.FixShape.FixEdgeSameParameterMode : -1 ToV4.FixShape.FixSelfIntersectingEdgeMode : -1 ToV4.FixShape.FixIntersectingEdgesMode : -1 ToV4.FixShape.FixNonAdjacentIntersectingEdgesMode : -1 ! ============================================================================== ! ! Parameters for EUCLID3 ! ------------------------------------------------------------------------------ ! Conversion EUCLID3 -> BRep FromE3.TraceFileName : /tmp/fromeuclid3.log FromE3.TraceFileAppend : 0 FromE3.TraceLevel : 2 FromE3.DropConnectivities : 0 FromE3.KeepE3I : 0 ! ------------------------------------------------------------------------------ ! Conversion BRep -> EUCLID3 ToE3.TraceFileName : /tmp/toeuclid3.log ToE3.TraceFileAppend : 0 ToE3.TraceLevel : 2 ToE3.Prepare : 1 ToE3.DropConnectivities : 0 ! Sequence of operators ToE3.exec.op : DirectFaces,ElementaryToRevolution,SplitAngle,SameParameter,SplitClosedFaces,SameParameter,FixFaceSize,BSplineRestriction,DropSmallEdges,FixGaps,BSplineRestriction,SameParameter,ToBezier ! complete ToE3.exec.op : see above ! partial ToE3.exec.op : DirectFaces,ElementaryToRevolution,SplitAngle,SameParameter,SplitClosedFaces,SameParameter,BSplineRestriction,SameParameter,ToBezier ! Parameters of operators ToE3.SplitAngle.Angle : 1.658 ToE3.SplitAngle.MaxTolerance : 0.1 ToE3.SplitAngle.SegmentSurfaceMode : 1 ToE3.SplitClosedFaces.NbSplitPoints : 2 ToE3.SplitClosedFaces.CloseTolerance : 0.05 ToE3.SplitClosedFaces.MaxTolerance : 0.1 ToE3.SplitClosedFaces.SegmentSurfaceMode : 1 ToE3.FixFaceSize.Tolerance : 0.05 ToE3.FixGaps.Tolerance3d : 0.05 ToE3.FixGaps.SurfaceMode : 0 ToE3.FixGaps.SurfaceAddSpans : 0 ToE3.FixGaps.SurfaceContinuity : C1 ToE3.FixGaps.NbIterations : 10 ToE3.FixGaps.Beta : 200.0 ToE3.FixGaps.Coeff1 : 0.0 ToE3.FixGaps.Coeff2 : 0.0 ToE3.FixGaps.Coeff3 : 10.0 ToE3.FixGaps.Coeff4 : 0.0 ToE3.FixGaps.Coeff5 : 0.0 ToE3.FixGaps.Coeff6 : 0.0 ToE3.FixGaps.MaxDeflection : 1.0 ToE3.DropSmallEdges.Tolerance3d : 0.05 ToE3.BSplineRestriction.SurfaceMode : 0 ToE3.BSplineRestriction.Curve3dMode : 1 ToE3.BSplineRestriction.Curve2dMode : 1 ToE3.BSplineRestriction.OffsetSurfaceMode : 0 ToE3.BSplineRestriction.OffsetCurve3dMode : 1 ToE3.BSplineRestriction.OffsetCurve2dMode : 1 ToE3.BSplineRestriction.LinearExtrusionMode : 1 ToE3.BSplineRestriction.RevolutionMode : 0 ToE3.BSplineRestriction.Tolerance3d : 1e-3 ToE3.BSplineRestriction.Tolerance2d : 1e-5 ToE3.BSplineRestriction.Continuity3d : C1 ToE3.BSplineRestriction.Continuity2d : C1 ToE3.BSplineRestriction.RequiredDegree : 9 ToE3.BSplineRestriction.RequiredNbSegments : 100 ToE3.BSplineRestriction.PreferDegree : 1 ToE3.BSplineRestriction.RationalToPolynomial : 1 ToE3.BSplineRestriction.MaxDegree : 9 ToE3.BSplineRestriction.MaxNbSegments : 10000 ToE3.BSplineRestriction.SegmentSurfaceMode : 1 ToE3.ToBezier.EdgeMode : 0 ToE3.ToBezier.SurfaceMode : 1 ToE3.ToBezier.PlaneMode : 1 ToE3.ToBezier.RevolutionMode : 1 ToE3.ToBezier.ExtrusionMode : 1 ToE3.ToBezier.BSplineMode : 1 ToE3.ToBezier.Curve3dMode : 0 ToE3.ToBezier.Curve2dMode : 1 ToE3.ToBezier.Line3dMode : 0 ToE3.ToBezier.Circle3dMode : 0 ToE3.ToBezier.Conic3dMode : 1 ToE3.ToBezier.MaxTolerance : 0.1 ToE3.ToBezier.SegmentSurfaceMode : 1 ToE3.ToBezier.MinCurveLength : 0.05 ToE3.FixShape.Tolerance3d : 1.e-7 ToE3.FixShape.MaxTolerance3d : 1.e-7 ToE3.FixShape.MinTolerance3d : 1.e-7 ToE3.FixShape.FixFreeShellMode : -1 ToE3.FixShape.FixFreeFaceMode : -1 ToE3.FixShape.FixFreeWireMode : -1 ToE3.FixShape.FixSameParameterMode : -1 ToE3.FixShape.FixSolidMode : -1 ToE3.FixShape.FixShellMode : -1 ToE3.FixShape.FixFaceMode : -1 ToE3.FixShape.FixWireMode : -1 ToE3.FixShape.FixOrientationMode : -1 ToE3.FixShape.FixMissingSeamMode : -1 ToE3.FixShape.FixSmallAreaWireMode : -1 ToE3.FixShape.ModifyTopologyMode : 0 ToE3.FixShape.ModifyGeometryMode : 1 ToE3.FixShape.ClosedWireMode : 1 ToE3.FixShape.PreferencePCurveMode : 1 ToE3.FixShape.FixReorderMode : -1 ToE3.FixShape.FixSmallMode : -1 ToE3.FixShape.FixConnectedMode : -1 ToE3.FixShape.FixEdgeCurvesMode : -1 ToE3.FixShape.FixDegeneratedMode : -1 ToE3.FixShape.FixLackingMode : -1 ToE3.FixShape.FixSelfIntersectionMode : -1 ToE3.FixShape.FixReversed2dMode : -1 ToE3.FixShape.FixRemovePCurveMode : -1 ToE3.FixShape.FixRemoveCurve3dMode : -1 ToE3.FixShape.FixAddPCurveMode : -1 ToE3.FixShape.FixAddCurve3dMode : -1 ToE3.FixShape.FixSeamMode : -1 ToE3.FixShape.FixShiftedMode : -1 ToE3.FixShape.FixEdgeSameParameterMode : -1 ToE3.FixShape.FixSelfIntersectingEdgeMode : -1 ToE3.FixShape.FixIntersectingEdgesMode : -1 ToE3.FixShape.FixNonAdjacentIntersectingEdgesMode : -1 ! Parameters for ICE ! ICE.DECODAGE_PLANS_3D :1 ICE.DIMENS_ENORME_CAR :100.000000 ICE.FILTRAGE_MICROCRB :0 ICE.DECODAGE_LIGNE_3D :1 ICE.EPSILON_FILTRE_2D :0.000020 ICE.DECODAGE_CURV_3D :1 ICE.MAX_PT/K_UNISURF3 :500 ICE.DECODAGE_SURF_3D :1 ICE.MAX_PT/B_UNISURF3 :500 ICE.DECODAGE_FACES_3D :1 ICE.MAX_BC/K_UNISURF3 :5 ICE.DECODAGE_CERCL_3D :1 ICE.MAX_CRB_RESTRI_U4 :63 ICE.DECODAGE_VOLUM_3D :1 ICE.MAX_SD_POINTS_U4 :30000 ICE.DECODAGE_MOCKUP3D :1 ICE.MAX_SD_LIAISON_U4 :30000 ICE.DECODAGE_SOLEX_3D :1 ICE.MAX_SD_ELEMENT_U4 :30000 ICE.RECUP_ERR_RESTRIC :1 ICE.UNITE_LOGIC_ECRAN :6 ICE.RECUP_ERR_APPROXI :1 ICE.LONGUEUR_REC_FT17 :3536 ICE.CLASSE_MAX_ADMISE :8 ICE.LONGUEUR_REC_FT16 :16 ICE.EPSILON_APPROX_3D :0.010000 ICE.DESTRUCT_OLD_FILE :1 ICE.LISTING_DECODAGE :0 ICE.DIMENS_MICRO_SURF :0.040000 ICE.METHODE_APPROX :0 ICE.FLECHE_DISCRET_2D :0.000004 ICE.DIMENS_MICRO_CURV :0.010000 ICE.DECODAGE_POINT_3D :1 ICE.COEF_FLECHE_3D/2D :1.000000 ICE.FILTRAGE_MICROSRF :1 ICE.IFL_SEA :-1 ICE.GENERIC_FILE_NAME :toto ! ============================================================================== ! ! Description of parameters ! Version : Name of the version ! *.MaxTolerance : Maximal tolerance for comparing curves, points which is ! used by splitting tools. The tools that are used this ! parameter are the following: SplitAngle, SplitClosedFaces, ! ToBezier. This value should be the same for all tools in ! one sequence. To redefine default value uncomment ! appropriate line in each operator. ! *.SegmentSurfaceMode : Mode for limiting surface by UV boundaries of face that ! is based on this surface. If flag is 1 the surface is ! limited. This mode is used by splitting tools (SplitAngle, ! SplitClosedFaces, ToBezier). This value should be the same ! for all tools in one sequence. To redefine default value ! uncomment appropriate line in each operator. ! Reject.FileName : Name of stored BRep file in the case of failure during Paste ! FromV4.FileName : Name of BRep file for Copy from CATIA ! FromV4.ConvCurvesToBezier : Mode of converting CATIA multi-arc curves, Bezier/B-Spline; forced if FromV4.ConvSurfacesToBezier is 1 ! FromV4.ConvSurfacesToBezier : Mode of converting CATIA multi-patch surfaces, Bezier/B-Spline ! FromV4.SameParameter : Mode for fixing SameParameter after conversion ! FromV4.TraceFileName : Name of trace file for Copy from CATIA ! FromV4.TraceFileAppend : Mode of appending trace file for Copy from CATIA, yes/no ! FromV4.TraceLevel : Level of detail in messages during Copy from CATIA ! FromV4.SharingFaces : Mode of copying free faces if they are shared by skin, yes/no ! ToV4.FileName : Name of BRep file for Paste to CATIA ! ToV4.CurveMerge : Mode of connection of faces in CATIA, yes/no ! ToV4.CreateSkin : Mode for creating skin after pasting a shell, yes/no. In any ! : case faces are translated and connectivities are computed. ! : In case of "yes" skin is created (if possible) on resulting faces. ! ToV4.ShortEdgeRemove : Mode of removing small edges, yes/no ! ToV4.ThinFaceRemove : Mode of removing small faces, yes/no ! ToV4.FillHoles : Mode of inserting an edge in the case of a gap greater than identicalcurve between consecutive edges, yes/no ! ToV4.Prepare : Mode of invoking sequence of operators during Paste to CATIA, yes/no ! ToV4.TraceFileName : Name of trace file for Paste to CATIA ! ToV4.TraceFileAppend : Mode of appending trace file for Paste to CATIA, yes/no ! ToV4.TraceLevel : Level of detail in messages during Paste to CATIA ! FromE3.TraceFileName : Name of trace file for Copy from EUCLID3 ! FromE3.TraceFileAppend : Mode of appending trace file for Copy from EUCLID3, yes/no ! FromE3.TraceLevel : Level of detail in messages during Copy from EUCLID3 ! FromE3.DropConnectivities : Mode of processing connectivities from EUCLID3, drop incorrect (0)/drop all(1)/drop incorrect and fix(2) ! FromE3.KeepE3I : Mode of keeping (1) or removing (0) intermediate E3I file ! ToE3.TraceFileName : Name of trace file for Paste to EUCLID3 ! ToE3.TraceFileAppend : Mode of appending trace file for Paste to EUCLID3, yes/no ! ToE3.TraceLevel : Level of detail in messages during Paste to EUCLID3 ! ToE3.Prepare : Mode of invoking sequence of operators during Paste to EUCLID3, yes/no ! ToE3.DropConnectivities : Mode of processing connectivities to EUCLID3, transfer all(0)/drop all (1) ! exec.op : Sequence of operators ! List of operators (sorted in alphabetical order) with their parameters ! BSplineRestriction : Approximation of general B-Spline and Bezier with particular B-Spline ! BSplineRestriction.SurfaceMode : Mode of approximation of surfaces, yes/no ! BSplineRestriction.Curve3dMode : Mode of approximation of 3D curves, yes/no ! BSplineRestriction.Curve2dMode : Mode of approximation of 2D curves, yes/no ! BSplineRestriction.OffsetSurfaceMode : Mode of conversion of offset surfaces to BSpline surface, yes/no ! : Yes - surface is converted to BSpline surface ! : No - basis surface is processed but offset surface is kept. ! : This mode acts if BSplineRestriction.SurfaceMode is yes. ! BSplineRestriction.LinearExtrusionMode: Mode of conversion of linear extrusion surfaces to BSpline surface, yes/no ! : Yes - surface is converted to BSpline surface ! : No - basis curve is processed but extrusion surface is kept. ! : This mode acts if BSplineRestriction.SurfaceMode is yes. ! BSplineRestriction.RevolutionMode : Mode of conversion surfaces of revolution to BSpline surface, yes/no ! : Yes - surface is converted to BSpline surface ! : No - basis curve is processed but revolution surface is kept. ! : This mode acts if BSplineRestriction.SurfaceMode is yes. ! BSplineRestriction.OffsetCurve3dMode : Mode of conversion of 3d offset curves to BSpline curves, yes/no ! : Yes - curve is converted to BSpline curve ! : No - basis curve is processed but offset curve is kept. ! : This mode acts if BSplineRestriction.Curve3dMode is yes. ! BSplineRestriction.OffsetCurve2dMode : Mode of conversion of 2d offset curves to BSpline curves, yes/no ! : Yes - curve is converted to BSpline curve ! : No - basis curve is processed but offset curve is kept. ! : This mode acts if BSplineRestriction.Curve2dMode is yes. ! BSplineRestriction.Tolerance3d : Tolerance of 3D approximation ! BSplineRestriction.Tolerance2d : Tolerance of 2D approximation ! BSplineRestriction.Continuity3d : Required continuity of 3D geometry ! BSplineRestriction.Continuity2d : Required continuity of 2D geometry ! BSplineRestriction.RequiredDegree : Required degree of B-Spline ! BSplineRestriction.RequiredNbSegments : Required maximum number of segments of B-Spline ! BSplineRestriction.PreferDegree : Preference between requirement to degree and maximum number of segments, true/false ! BSplineRestriction.RationalToPolynomial: Mode of conversion of rational B-Spline to polynomial, yes/no ! BSplineRestriction.MaxDegree : Maximum allowed degree of B-Spline ! BSplineRestriction.MaxNbSegments : Maximum allowed number of segments in a B-Spline ! DirectFaces : Conversion of elementary surface in left-handed coordinate system into right-handed ! no parameters ! ElementaryToRevolution : Conversion of elementary revolutive surface into general surface of revolution ! no parameters ! SameParameter : Conversion of edge to be SameRange and SameParameter ! SameParameter.Force : Mode of forced invoking, true/false ! SameParameter.Tolerance3d : 3D tolerance ! SplitAngle : Split revolutive surface (elementary and general) into several surfaces ! SplitAngle.Angle : Maximum angle of revolution, radian ! SplitClosedFaces : Split faces that have seam-edge or geometrically closed on closed surface. ! SplitClosedFaces.NbSplitPoints : Number of cuttings (number of resulting faces will be NbSplitPoints+1) ! SplitClosedFaces.CloseTolerance : Precision to define geometric closure. ! SplitContinuity : Correction or split shapes to have speicified continuity ! SplitContinuity.Tolerance3d : 3D tolerance for correction of geometry ! SplitContinuity.SurfaceContinuity : Required continuity for surfaces ! SplitContinuity.CurveContinuity : Required continuity for curves ! SurfaceToBSpline : Conversion of surface (of types given below) to B-Spline ! : Obsolete. It is strongly recommended to ! : use BSplineRestriction ! SurfaceToBSpline.LinearExtrusionMode : Mode of conversion of surfaces of linear extrusion, yes/no ! SurfaceToBSpline.RevolutionMode : Mode of conversion of surfaces of revolution, yes/no ! SurfaceToBSpline.OffsetMode : Mode of conversion of offset surfaces, yes/no ! ToBezier : Conversion of geometry into Bezier ! ToBezier.SurfaceMode : Mode of conversion of surfaces, yes/no ! ToBezier.PlaneMode : Mode of conversion of Planes,yes/no. This mode acts if SurfaceMode is yes. ! ToBezier.RevolutionMode : Mode of conversion of Surfaces of Revolution (generatrix to bezier), yes/no. ! This mode acts if SurfaceMode is yes. ! ToBezier.ExtrusionMode : Mode of conversion of Surfaces of Extrusion (whole surface not only generatrix), yes/no. ! This mode acts if SurfaceMode is yes. ! ToBezier.BSplineMode : Mode of conversion of BSpline Surfaces, yes/no. This mode acts if SurfaceMode is yes. ! ToBezier.EdgeMode : Mode of translation edges (0- Free,1 - Shared,2- Both) ! : .Default - Free. Acts on translation curves 3d . | : If it is 0 (Free) that only free edges are taken into ! : account for translation 3d curves, ! : if it is 1 (Shared) that only shared edges are taken into ! : account for translation 3d curves, ! : if it is 2 (Both) that all edges are taken into ! : account for translation 3d curves, ! ToBezier.Curve3dMode : Mode of conversion 3D curves, yes/no ! ToBezier.Curve2dMode : Mode of conversion 2D curves, yes/no ! ToBezier.Line3dMode : Mode of conversion 3D lines, yes/no ! ToBezier.Circle3dMode : Mode of conversion 3D circles, yes/no ! ToBezier.Conic3dMode : Mode of conversion 3D conics, yes/no ! ToBezier.MinCurveLength : Min length of created curves 3d.( default 0.05) ! ToCATIAGeom : Conversion of shapes to CATIA multi-arcs and multi-patches ! no parameters ! FixFaceSize : Removing small faces ! FixFaceSize.Tolerance : Tolerance in 3d ! FixGaps : Removing gaps between edges in wires and between 3d curves of edges and faces ! FixGaps.Tolerance3d : Tolerance (3d) ! FixGaps.SurfaceMode : Mode of fixing gaps between edges and faces (yes/no) ! FixGaps.SurfaceAddSpans : Number of spans to add to the surface in order to fix gaps ! FixGaps.SurfaceContinuity : Minimal continuity of resulting surface ! FixGaps.NbIterations : Number of iterations ! FixGaps.Beta : Elasticity coefficient for modifying surface [1-1000] ! FixGaps.Coeff1..6 : Energy coefficients for modifying surface [0-10000] ! FixGaps.MaxDeflection : Maximal deflection of surface from old position ! DropSmallEdges : Eliminate small edges by removing or merging with neighbour ! DropSmallEdges.Tolerance3d : Tolerance (3d) ! FixShape.Tolerance3d : Tolerance (3d) for fixing of shape. ! FixShape.MaxTolerance3d : Maximal possible value of increasing of tolerance during fixing. ! FixShape.MinTolerance3d : Minimal value of tolerance. ! FixShape.FixFreeShellMode : Mode for fixing free shells in the shape (default - -1, yes - 1 , no - 0). ! FixShape.FixFreeFaceMode : Mode for fixing free faces in the shape (default - -1, yes - 1 , no - 0). ! FixShape.FixFreeWireMode : Mode for fixing free wires in the shape (default - -1, yes - 1 , no - 0). ! FixShape.FixSameParameterMode : Mode for fixing same parameter on the whole shape (default - -1, yes - 1 , no - 0). ! FixShape.FixSolidMode : Mode for fixing solids (default - -1, yes - 1 , no - 0). ! FixShape.FixShellMode : Mode for fixing shells (default - -1, yes - 1 , no - 0). ! FixShape.FixFaceMode : Mode for fixing faces (default - -1, yes - 1 , no - 0). ! FixShape.FixWireMode : Mode for fixing wires (default - -1, yes - 1 , no - 0). ! FixShape.FixOrientationMode : Mode for fixing face orientation (default - -1, yes - 1 , no - 0). ! FixShape.FixMissingSeamMode : Mode for fixing face missing seam (default - -1, yes - 1 , no - 0). ! FixShape.FixSmallAreaWireMode : Mode for fixing small area wires (default - -1, yes - 1 , no - 0). ! FixShape.ModifyTopologyMode : Mode allowing of modifing of topology (default - 0, yes - 1 , no - 0). ! FixShape.ModifyGeometryMode : Mode allowing of modifing of geometry (default - 1, yes - 1 , no - 0). ! FixShape.ClosedWireMode : Mode defining whether the wire is to be closed. (default - 1, yes - 1 , no - 0). ! FixShape.PreferencePCurveMode : Mode defining of preference of 2d representation (default - 1, yes - 1 , no - 0). ! FixShape.FixReorderMode : Mode for fixing of order of the edges in the wire (default - -1, yes - 1 , no - 0). ! FixShape.FixSmallMode : Mode for removing of the small edges from the wire in the case when ! : ModifyTopologyMode equaled "yes" (default - -1, yes - 1 , no - 0). ! FixShape.FixConnectedMode : Mode for fixing of connecting of edges in the wire(default - -1, yes - 1 , no - 0). ! FixShape.FixEdgeCurvesMode : Moge for fixing each edge from the wire (default - -1, yes - 1 , no - 0). ! FixShape.FixDegeneratedMode : Moge for fixing cases of degenerate pcurve (default - -1, yes - 1 , no - 0). ! FixShape.FixLackingMode : Moge for fixing cases of lacking edge (default - -1, yes - 1 , no - 0). ! FixShape.FixSelfIntersectionMode : Mode for fixing of cases self-intersection of wire (default - -1, yes - 1 , no - 0). ! FixShape.FixReversed2dMode : Mode for fixing cases when pcurve is opposite curve3d (default - -1, yes - 1 , no - 0). ! FixShape.FixRemovePCurveMode : Mode for removing of pcurves from edges (default - -1, yes - 1 , no - 0). ! FixShape.FixRemoveCurve3dMode : Mode for removing of 3d curves from edges (default - -1, yes - 1 , no - 0). ! FixShape.FixAddPCurveMode : Mode for adding pcurves of the edges if missing (default - -1, yes - 1 , no - 0). ! FixShape.FixAddCurve3dMode : Mode for adding curves 3d of the edges if missing (default - -1, yes - 1 , no - 0). ! FixShape.FixSeamMode : Mode for fixing cases of seam edges. ! FixShape.FixShiftedMode : Mode for fixing cases when pcurves can be shifted on period on the closed surface ! (default - -1, yes - 1 , no - 0). ! FixShape.FixEdgeSameParameterMode : Mode for fixing same parameter for each edge (default - -1, yes - 1 , no - 0). ! FixShape.FixSelfIntersectingEdgeMode : Mode for fixing cases self-intrsection edge (default - -1, yes - 1 , no - 0). ! FixShape.FixIntersectingEdgesMode : Mode for fixing intersection adjacent edges. ! FixShape.FixNonAdjacentIntersectingEdgesMode : Mode for fixing intersection non-adjacent edges.